Whalecome: How to paint perfect letters

I have always thought that Whalecome is the funniest word ever. Since the first time I heard it that is (yes I realize its not a real word). It would not be funny for everyone I guess, just nautical lovers probably. I have wanted to make a pillow that says Whalecome for a long time now and I finally did! In fact. I made 2. One for Joss (the sailboat in other posts) and one for Ca-Sea-Ta (my in-laws other boat).

 You can't deny that is the cutest thing ever!

Materials:

Pillowcase or other surface

Paint

Print-out of picture/writing on any type of printer paper

Sharp Ballpoint Pen

Paintbrush

Sponge

Scissors

What I did:

I chose to put this stencil onto a pillow case, I have also done a similar project on a piece of fabric to make a type of flag. This can also be done on wood, or many other options. 

First cut out the large area with the scissors. The whale in this picture was easy to cut with scissors, but once I got to the letters is when I had to get creative. They were too skinny for my scissors, and my exacto knife ripped the paper so there was not a straight edge. 

Tape the word onto the fabric where you would like it to be so that it does not move. You might need to cut down the paper to include only the letters.

Use your pen to puncture holes in the paper. Once you are done the full word it should look something like this. 

Take the paper off and underneath should look something like this. The second time I did this project I used way less dots because I realized I did not need so many. Less dots = faster.

Consider taking the tape off slowly incase your pen died or a letter was missed for some reason.

Paint inside the dots. 

Finally use the sponge to paint inside the whale stencil. (I painted the whale first, order does not matter) A sponge will give the best results with the paper because you will be only dabbing the fabric. There is almost no chance that the stencil will run on the edges. 

Finished!

Sore Bum: Stool pillow top

A log stool is just a log if you don't spruce it up!

My log stool was hard and not that exciting until I added a pillow top to it!

Materials:

Stiff Fabric

Foam or Round Pillow

Long screw

Washer the bigger the better

Big Button

Strong glue

First determine how big to make the pillow. I made mine 1" wider than my stump so that it had some overhang. I had some old foam lying around so I cut that to the right size. I wanted the seat to be soft, so I cut an additional circle slightly smaller to go on top for extra padding. If you are using a pillow skip this step.

Making a pillow, I quickly learned, is a very simple task and does not require a pattern. Measure the diameter of the foam and add 3" total to the measurement to account for the 1.5" seam on each side. Fold your fabric in half and cut a circle out of your fabric with the new diameter. To cut a circle I tied a pencil on one end of a string and cut the sting to be the correct length. Hold the sting in the middle and draw a circle with the pencil all the way around keeping the sting tight. It was not 100% accurate for me, but it should be close enough that it will correct when you sew it together. 

Next measure the distance around the outside of the newly cut circles Add a few inches for 'safety' this will be the side panel. Measure the height of your foam/pillow. Mine was 6" tall but I wanted it to squish down inside my pillow case so I only cut 6" total (3" + 1.5" seams on each side). 

Fold the side panel stip in half, and in half again. Pin the corners (3 pins and 4 even sections). Next fold the one circle in half and pin the edges (do this both ways so there are 4 pins dividing the quarters). Match the pins so that the side panel stip is evenly dispursed around the circle. Make sure you do this right side to right side (so when you flip it inside out you see the good side of the fabric). 

Sew the circle on to the side panel strip. Do it again for the other circle but only sew 3/4 of the way around. 

Put the pillow or foam pieces inside and hand sew the opening closed. 

Take a long screw. Mine was 5" but that might have been over kill. Place the washer on the screw. This gives extra security so the fabric doesn't rip and pop over top of the screw. Place the pillow on the stump just how you want it. Find the middle of the pillow (I eyeballed it) and screw down through the pillow into the stup. Go down almost as far as you can so that when you sit down the screw doesn't poke you. Finally glue a big button on top of the screw to hide it.

Finished!